5.00/
ELI-S-100
Brand: Philips Bodine
See PRODUCT DESCRIPTION below
Starting at $786.25
PRODUCT VARIATIONS
DESCRIPTION
APPLICATION
The Philips Bodine ELI-S-100 Emergency Lighting Inverter works in conjunction with a fluorescent or LED fixture to create an emergency lighting system. The ELI-S-100 operates a maximum load of 100 W at unity power factor. It allows the connected fixture(s) to be on, off, switched or dimmed without affecting emergency operation. Each unit consists of two sealed lead acid batteries, charger and electronic circuitry in one steel case. The ELI-S-100 provides power to the input side of the fixture, including AC ballast/driver, and can be used with indoor or outdoor emergency fixture applications. The ELI-S-100 is not suitable for use with HID sources.
OPERATION
Upon failure of normal power, the ELI-S-100 instantly begins providing emergency power to the connected lighting load for a minimum of 90 minutes. A solid-state low voltage disconnect circuit protects the inverter battery from severe damage by deep discharge during prolonged power failures. When normal power is restored, the ELI-S-100 automatically returns to charge mode. The battery capacity is fully restored in 24 hours. Isolated dry-contact relays (2 each) are also provided to override local dimming controls used in normal mode, when luminaires are driven from AC power mains.
DIMMING
The ELI-S-100 features a dimming control output of 0-10 volts. This dimming capability allows a higher power fixture to operate at a dimmed 100 W maximum emergency-mode lighting level - or, alternately, it allows a string of multiple fixtures to be driven in emergency mode at a combined 100 W maximum. For example, four 100W LED fixtures may be connected to one ELI-S-100 and dimmed for emergency operation to 20% of normal power, with each LED fixture supplying 20W of output power (20W x 4 = 80W).* The emergency mode output dimming voltage is field settable in 5 steps to provide nominally 20%, 40%, 60%, 80%, or 100% light output. The installer will set the dimming level by operating the dip switches which are located at the lower center section of the circuit board. See illustrations.
*Note: Dimming drivers are less efficient at reduced power. This inefficiency must be accounted for in the design.
INSTALLATION
The ELI-S-100 does not affect normal fixture operation and may be used with a switched or unswitched fixture. It can be installed in close proximity to the fixture or remote from the fixture (up to 250 feet).
The Philips Bodine ELI-S-100 Emergency Lighting Inverter works in conjunction with a fluorescent or LED fixture to create an emergency lighting system. The ELI-S-100 operates a maximum load of 100 W at unity power factor. It allows the connected fixture(s) to be on, off, switched or dimmed without affecting emergency operation. Each unit consists of two sealed lead acid batteries, charger and electronic circuitry in one steel case. The ELI-S-100 provides power to the input side of the fixture, including AC ballast/driver, and can be used with indoor or outdoor emergency fixture applications. The ELI-S-100 is not suitable for use with HID sources.
OPERATION
Upon failure of normal power, the ELI-S-100 instantly begins providing emergency power to the connected lighting load for a minimum of 90 minutes. A solid-state low voltage disconnect circuit protects the inverter battery from severe damage by deep discharge during prolonged power failures. When normal power is restored, the ELI-S-100 automatically returns to charge mode. The battery capacity is fully restored in 24 hours. Isolated dry-contact relays (2 each) are also provided to override local dimming controls used in normal mode, when luminaires are driven from AC power mains.
DIMMING
The ELI-S-100 features a dimming control output of 0-10 volts. This dimming capability allows a higher power fixture to operate at a dimmed 100 W maximum emergency-mode lighting level - or, alternately, it allows a string of multiple fixtures to be driven in emergency mode at a combined 100 W maximum. For example, four 100W LED fixtures may be connected to one ELI-S-100 and dimmed for emergency operation to 20% of normal power, with each LED fixture supplying 20W of output power (20W x 4 = 80W).* The emergency mode output dimming voltage is field settable in 5 steps to provide nominally 20%, 40%, 60%, 80%, or 100% light output. The installer will set the dimming level by operating the dip switches which are located at the lower center section of the circuit board. See illustrations.
*Note: Dimming drivers are less efficient at reduced power. This inefficiency must be accounted for in the design.
INSTALLATION
The ELI-S-100 does not affect normal fixture operation and may be used with a switched or unswitched fixture. It can be installed in close proximity to the fixture or remote from the fixture (up to 250 feet).
